Start with your town’s water report
Every community water system has to publish an annual water quality report, also called a Consumer Confidence Report. Search for your water company’s name plus “water quality report,” or check the back of a water bill. New York City’s Department of Environmental Protection publishes one report for the whole city.
When you open it, look for three things: where your water comes from, which contaminants were detected and how those levels compare to the legal limit, and whether there were any violations. A detection on its own isn’t a red flag. Utilities test for extremely small amounts, and the report shows you how close each result is to the limit.
PFAS: New Jersey moved early
PFAS are a large family of man-made chemicals used in nonstick, stain-resistant, and waterproof products. They break down very slowly, which is why they’re often called “forever chemicals.” New Jersey was one of the first states to regulate them in drinking water, setting limits of 14 parts per trillion for PFOA and 13 ppt for PFOS in 2020, years before there was a national standard.
In 2024, EPA set national limits of 4 ppt for PFOA and PFOS, with water systems required to comply by 2029. In May 2026, EPA proposed keeping those two limits, dropping the limits it had set for several other PFAS, and letting some systems request two more years, until 2031. That proposal hadn’t been finalized at the time of writing, so expect more headlines.
In practical terms, some New Jersey systems that already meet the state limits will still need upgrades to reach 4 ppt. Your annual report lists PFAS results. If the numbers concern you, look for a point-of-use filter certified under NSF/ANSI 53 or 58 specifically for PFOA and PFOS reduction, and confirm that the exact model is listed for that claim.
Lead comes from pipes, not the reservoir
Lead rarely comes from the source water. It gets in along the way, from lead service lines (the pipe that connects a building to the water main), old lead solder, and some older brass fixtures. Homes built before 1986, when federal law banned lead pipes and solder for drinking water, are the most likely to have lead somewhere in the plumbing.
New Jersey passed a law in 2021 requiring water systems to replace every lead service line in the state by July 2031, and utilities have been working through their inventories since. New York City’s DEP says the water leaving its reservoirs is lead-free, so in the city the risk comes from building plumbing. NYC residents can request a free lead test kit by calling 311 or ordering online.
- If water has been sitting in the pipes for several hours, run the cold tap until it feels noticeably colder before drinking.
- Use cold water for drinking, cooking, and baby formula. Hot water pulls more lead out of pipes.
- If you want a filter for lead, look for NSF/ANSI 53 or 58 certification for lead reduction, not just a general claim.
Hard water: annoying, but not a health problem
Hard water is simply water with a lot of dissolved calcium and magnesium. It isn’t a health risk. It’s what leaves white crust on faucets and showerheads, spots on glasses, scale inside kettles, and soap that won’t lather.
The U.S. Geological Survey classifies hardness this way: 0 to 60 mg/L is soft, 61 to 120 is moderately hard, 121 to 180 is hard, and anything above 180 is very hard. Water reports sometimes list hardness in grains per gallon instead. One grain is about 17.1 mg/L.
New York City’s water comes from upstate reservoirs and is soft. In New Jersey, hardness varies a lot from one town to the next, and systems that draw from groundwater tend to be harder than those that rely on reservoirs. If scale is building up all over the house, a whole-home water softener is the fix for that. Keep in mind that a softener is a separate decision from a drinking-water filter, because it isn’t designed to remove things like lead or PFAS.
On a private well? You’re the water company
If your home has a private well, no utility is testing your water. New Jersey’s Private Well Testing Act requires a test when a home with a well is sold, but between sales, testing is up to you. The CDC recommends testing a private well at least once a year for coliform bacteria, nitrates, total dissolved solids, and pH, and your local health department can tell you what else is worth checking in your area. Test before you buy any treatment equipment, so you know what you’re actually treating.
So do you need a filter?
Crystal can go through your water report with you and check which Coway models carry certifications that match what you’re concerned about. And if your water looks fine and you’re happy with how it tastes, that’s a perfectly good answer too.
- Your report shows a contaminant you’re worried about: choose a filter certified to reduce that specific contaminant.
- Older building that may have lead plumbing: test first, then consider a filter certified for lead reduction.
- Water is safe but tastes or smells like chlorine: a carbon filter certified under NSF/ANSI 42 for taste and odor is usually enough.
- Scale on fixtures and appliances: a water softener, not a drinking-water filter.
- Private well: get it tested before buying anything.
Continue exploring
Sources and further reading
- EPA: Consumer Confidence Reports (annual water quality reports) ↗
- EPA: PFAS National Primary Drinking Water Regulation ↗
- NJDEP: PFAS in New Jersey ↗
- NJDEP: Lead in drinking water and lead service lines ↗
- EPA: Basic information about lead in drinking water ↗
- NYC DEP: Free lead in drinking water test kit ↗
- NYC DEP: Drinking Water Supply & Quality Report ↗
- USGS: Hardness of water ↗
- NJDEP: Private Well Testing Act ↗
- CDC: Guidelines for testing well water ↗
Educational information only. Product performance depends on the specific model, installation, maintenance, and certified reduction claims.
